Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 66

Page: 66 / 92

[email protected]

Step 25: Attach Access Ladder/Rockwall Assembly to Fort

Pre-drill all holes using a 3/16” drill bit before

installing the Lag Screws

Remove (0705) Cedar Wall from the Access

Ladder Rockwall, previously assembled in Step 2. Set

the board and screws aside, they will be re-attached.

(fig. 25.2)

Place the Access Ladder Rockwall centred in

between (2181) Short Post and (2180) Post on the

Back Wall, flush to top of floor boards, then attach to

(2164) Floor Support with 1 (LS1) 1/4 x 1-1/2” Lag

Screw (with flat washer) in each Swing Bracket. (fig.

25.1, 25.2 and 25.3).

Re-attach (0705) Cedar Wall to the same place it

was removed.

Hardware

3 x

1/4 x 1-1/2” Lag Screw (1/4”flat washer)

LS1

0705

Fig. 25.1

1/4” flat

washer

Back Wall

Fig. 25.2

Fig. 25.3

2180

2181

2164

0705

1/4” flat

washer

2164

LS1

Flush

Note: Access Ladder

Rockwall is centred in

opening

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands