Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 58

Page: 58 / 92

[email protected]

Step 21: Upper Front Wall Assembly

Part 4

Tight to the bottom of (2240) Gable Bottom attach (2238) Filler to (2180) Post, (2236) Back Wall and (2181)

Short Post with 3 (S1) #8 x 1-1/8” Wood Screws. (fig. 21.5)

: Tight to the bottom of (2238) Filler attach 1 (2232) Siding to (2180) Post, both (2237) Back Wall, (2236) Back

Wall and (2181) Short Post with 5 (S0) #8 x 7/8” Truss Screws. (fig. 21.5)

Tight to the bottom of (2232) Siding attach 1 (2235) Wall to (2180) Post, both (2237) Back Wall, (2236) Back

Wall and (2181) Short Post with 7 (S0) #8 x 7/8” Truss Screws. (fig. 21.5)

Measure 13-1/2” from the bottom of (2235) Wall and attach a second (2235) Wall to (2180) Post, both (2237)

Back Wall, (2236) Back Wall and (2181) Short Post with 7 (S0) #8 x 7/8” Truss Screws. (fig. 21.5)

Hardware

Wood Parts

2238

3 x

#8 x 1-1/8” Wood Screw

19 x

#8 x 7/8” Truss Screw

1 x

Filler 1 x 2 x 44”

2 x

Wall 1/2 x 4 x 44”

1 x

Siding 3/8 x 3-1/2 x 44”

2238

2235

13-1/2”

2181

2180

Tight

2240

2237

2236

2245

Fig. 21.5

Outside View

2232

x 12

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands