Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 29

Page: 29 / 92

[email protected]

Hardware

Wood Parts

3 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 2-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

#8 x 1-1/2” Wood Screw

4 x

1/4” t-nut

H11

2 x

Short Post 2 x 4 x 49-3/4”

1 x

Front Rail 1 x 6 x 23”

2181

2183

Step 8: Front Wall Assembly

Part 2

With bevelled ends facing up loosely attach 2 (2181) Short Posts to (2164) Floor Support with 1 (H11) 1/4 x

2-3/4” Hex Bolt (with lock washer, flat washer and t-nut) per board. Hex bolts to be installed from the inside of

the assembly. (fig. 8.3)

Loosely attach (2183) Front Rail to each (2181) Short Post and to (2182) Mid Post with 3 (H2) 1/4 x 2” Hex

Bolt (with lock washer, flat washer and t-nut). Hex bolts to be installed from the outside of the assembly. (fig.

8.3 and 8.4)

Make sure assembly is square and ensure that the spacing between (2180) Post and (2179) Ground Front

is 27-5/8” (fig. 8.3), then tighten all bolts and attach (2183) Front Rail to each (2181) Short Post with 2 (S2) #8 x

1-1/2” Wood Screws. (fig. 8.3 and 8.4)

Install one 1/4” T-nut into (2180) Post,

(2182) Mid Post and each

(2181) Short Post on the inside

of the assembly, as shown

in fig.8.3 and 8.5.

Inside View

Fig. 8.3

H11

2164

2181

2182

1/4” lock

washer

1/4” flat

washer

1/4” t-nut

Notice bevelled

edge facing up

Fig. 8.4

Outside View

2183

2181

1/4” t-nut x 4

2183

27-5/8”

2180

2179

Fig. 8.5

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands