Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 44

Page: 44 / 92

[email protected]

Step 18: Door Wall Assembly

Part 1

Measure the distance between (2179) Door Post and

(2182) Mid Post to make sure it is 17-1/2”. If it does not

meet this measurement loosen all bolts in (2179) Door Post

and (2182) Mid Post, move posts until you achieve this

measurement then re-tighten the bolts. (fig. 18.1)

On the Front Wall attach (2186) Back Front Wall to (2180)

Post, (2182) Mid Post and to both (2181) Short Posts with

4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and

previously installed t-nut) and 2 (S2) #8 x 1-1/2” Wood Screws

as shown in fig. 18.2 and 18.3. Notice the screw holes are

towards the bottom of the board.

Fig. 18.2

2182

2181

2179

2180

Fig. 18.1

Fig. 18.3

Wood Parts

Hardware

2 x

#8 x 1-1/2” Wood Screw

4 x

1/4 x 2” Hex Bolt

(1/4” lock washer, 1/4” flat washer, previously installed 1/4” t-nut)

1 x

Back Front Wall 1 x 6 x 69-1/2”

2186

Front

Loosen

these bolts

if needed

1/4” lock

washer

1/4” flat

washer

Notice screw

hole location

Slide

Wall

Swing

Wall

2182

2186

2181

17-1/2”

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands