Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 86

Page: 86 / 92

[email protected]

Step 37: Slide Support Assembly

Part 5

Place (0826) Short Upright, from Step 37.1, under the bottom section of the slide, in the rails between

emboss #1 and #2, as shown in fig. 37.9 and 37.10. (0826) Short Upright must be plumb. Mark location on the

ground then remove the board.

Dig one, flat bottom, 8” wide by 6” deep hole as previously done in Step 37, Part 2. Place (0826) Short

Upright in the hole, making sure that it is still plumb. (fig. 37.10)

Refill hole halfway with soil and compact making sure (0826) Short Upright stays plumb. Finish filling and

compacting. (fig. 37.10)

Fig. 37.9

Fig. 37.10

Bottom

Section

Emboss #1

Emboss #2

Emboss #3

View From Under

Bottom Section

0826

Rail

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands