Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 69

Page: 69 / 92

[email protected]

Step 27: Upper Back Wall Assembly

Part 2

Tight to the bottom of (2243) Large Support L and (2244) Large Support and flush to the outside edges of

(2180) Post and (2181) Short Post attach (2174) Back Arch to (2180) Post and (2181) Short Post with 4 (S2) #8

x 1-1/2” Wood Screws. (fig. 27.2)

Measure 9-1/2” from both (2180) Post and (2181) Short Post, then place 1 (0850) CE Wall Board at each

marked out location, each flush to the top of (2174) Back Arch and attach to (2174) Back Arch and (2186) Back

Front Wall with 4 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 27.2 and 27.3)

Hardware

Wood Parts

1 x

Back Arch 1 x 6 x 48-7/8”

2 x

CE Wall Board 1 x 4 x 17”

2174

4 x

#8 x 1-1/2” Wood Screw

8 x

#8 x 1-1/8” Wood Screw

0850

2180

2181

Outside View

Fig. 27.2

Inside View

Fig. 27.3

2180

2244

2243

2186

0850

Flush

2174

0850

9-1/2”

(dimension for

both sides)

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands