Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 57

Page: 57 / 92

[email protected]

Step 21: Upper Front Wall Assembly

Part 3

On the outside of the assembly attach (2245) Long Trim flush to the outside edge of (2180) Post with 4 (S1)

#8 x 1-1/8” Wood Screws. The bottom of the board should be tight to (2186) Back Front Wall. (fig. 21.4)

Between (2183) Front Rail and (2186) Back Front Wall attach (2246) Mid Trim flush to outside edge of (2181)

Short Post with 3 (S1) #8 x 1-1/8” Wood Screws. (fig. 21.4)

Between (2183) Front Rail and (2244) Large Support attach (2247) Short Trim flush to outside edge of (2181)

Short Post with 2 (S1) #8 x 1-1/8” Wood Screws. (fig. 21.4)

Hardware

Wood Parts

2244

9 x

#8 x 1-1/8” Wood Screw

1 x

Long Trim 1 x 3 x 41-9/16”

1 x

Mid Trim 1 x 3 x 21-1/4”

1 x

Short Trim 1 x 3 x 14-7/8”

2245

2246

2247

2186

2181

2180

Fig. 21.4

Outside View

Tight

2243

2183

Tight

Flush

2245

2247

2246

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands