Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 34

Page: 34 / 92

[email protected]

Step 11: Slide Wall Assembly

4 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 4-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

SL Ground 1 x 5 x 38-1/2”

1 x

SL End 2 x 4 x 38-1/2”

2189

2187

Fig. 11.1

2189

2181

Loosely attach (2189) SL Ground to the outside of each (2182) Mid Post with 4 (H4) 1/4 x 4” Hex Bolts (with

lock washer, flat washer and t-nut). (fig. 11.1 and 11.2)

With the bolt holes towards the bottom of the board loosely attach (2187) SL End to each outside (2181)

Short Post with 2 (H6) 1/4 x 4-3/4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 11.1 and 11.3)

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Hardware

Wood Parts

Fig. 11.2

Front Wall

Back Wall

Notice bolt

hole location

Parts removed

for clarity

Fig. 11.3

2182

2181

Parts removed

for clarity

2187

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands