Cedar Summit F23135 Installation And Operating Instructions Manual Download Page 33

Page: 33 / 92

[email protected]

Step 10: Swing Wall Assembly

Part 2

4 x

1/4 x 4-1/2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

5/16 x 4-1/2” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

1 x

SW Top 5/4 x 6 x 38-1/2”

1 x

SW Mount 2 x 4 x 29”

2196

2194

Fig. 10.4

2180

2194

2196

Above (2188) SW End loosely attach (2196) SW Top to both (2180) Posts using 4 (H5) 1/4 x 4-1/2” Hex Bolts

(with lock washer, flat washer and t-nut). (fig. 10.3 and 10.4)

Loosely attach (2194) SW Mount to (2188) SW End and (2196) SW Top with 2 (G5) 5/16 x 4-1/2” Hex Bolts

(with lock washer, flat washer and t-nut). (fig. 10.3 and 10.5)

2188

5/16” flat

washer

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Hardware

Wood Parts

Fig. 10.3

Front Wall

Back Wall

Notice hole

location

towards top

5/16” lock

washer

5/16”

t-nut

Fig. 10.5

2196

2188

Summary of Contents for F23135





























































































Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands

Cedar Summit F23135, Installation And Operating Instructions Manual

Search results

Summary of Contents for F23135

Reviews:

Related manuals for F23135

Brands by name

Popular brands