background image

11

The bell located in the upper-right part of the screen lights 
when any fault is detected.
 
By default, the parameters are presented in metric units. 
For more information on how to change the system of 
measurement, see section 5.8.3.

5.5 - Start the unit

With the unit in the Local off mode, press the 

Start/Stop

 

button 

 to display the list of operating modes and 

select the required mode.

Local On

Local On: The unit is in the local control mode and allowed to 
start.

Local 
Schedule

Local Schedule: The unit is in the local control mode and 
allowed to start if the period is occupied.

Network

Network: The unit is controlled by network commands and 
allowed to start if the period is occupied.

Remote

Remote: The unit is controlled by external commands and 
allowed to start if the period is occupied.

Master

Master: The unit operates as the master in the master/slave 
assembly and allowed to start if the period is occupied.

IMPORTANT: When entering the menu, please note that 
the currently selected item corresponds to the last running 
operating mode. 

5.6 - Stop the unit

To stop the unit, press the 

Start/Stop

 button 

Confirm the unit shutdown by pressing 

Confirm Stop

 or 

cancel the unit shutdown by pressing the  

Back

 button  

5.3 - Read the welcome screen

The Welcome screen is the first screen shown after starting 
the user interface. It displays the application name as well 

as the current software version number.

Home button 

Software version number 

To exit the Welcome screen, press 

Information message box

The information box displayed in the status bar at the 
bottom of the screen includes relevant messages regarding 
the current user action.

All screens presented further in this manual may display 
the following messages:

MESSAGE

STATUS

COMMUNICATION FAILURE!

Equipment controller did not respond while 
reading the table content.

ACCESS DENIED!

Equipment controller denies access to one of 
the tables.

LIMIT EXCEEDED!

The value entered exceeds the parameter limit.

Save changes?

Modifications have been made. The exit must be 

confirmed by pressing Save or Cancel.

HIGHER FORCE IN EFFECT!

Equipment controller rejects Force or Auto 
command.

5.4 - Explore the synoptic screen

The Synoptic screen provides an overview of the system 
control, allowing the user to monitor the vapour-refrigeration 
cycle. 

The diagram indicates the current status of the unit, giving 
information on the unit capacity, the status of water heat 

exchanger pumps, and the pre-defined setpoint parameter.

All unit functions can be accessed by pressing the 

Main 

menu

 button 

IMPORTANT: The synoptic screen display may vary 

depending on pumps configuration.

Outdoor air temperature

Unit capacity percentage

3 Setpoint

Evaporator inlet and outlet water temperature

Status screen message

Shows the last 
mode selected

Summary of Contents for Touch Pilot Junior





































Reviews: