Canon Mk1500 User Manual Download Page 2

Page: 2 / 119

Regulations for this product FCC Regulations

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual.

If such changes or modifications should be made, you could be required to stop operation of the equipment.

Trademarks

• "Canon" and the Canon logo are the registered trademarks or the trademarks of Canon Inc.

Notices

• The contents of this document may not be duplicated in whole or in part by any means without

permission.

• The information in this document is subject to change without notice.

• In no event shall Nisca Corporation bear any responsibility for any direct or indirect damages arising

from the use of our product.

• In no event shall Nisca Corporation bear any responsibility for any direct or indirect damages resulting

from the improper use of our product by the customer, or from modifications or changes made to our

product by the customer.

• If you find any errors or omissions in this document, or if you have any questions concerning this

document, contact your nearest dealer.

• The data created/saved with this printer cannot be backed up in another storage device such as the

hard disk of the PC. We assume no responsibility for the loss caused by data disappearance due to a

machine failure, repair, inspection, or weak battery as well as the carry-over loss.

Summary of Contents for Mk1500
























































































































Search results

Summary of Contents for Mk1500

Reviews:

Canon Mk1500, User Manual, Page: 2 / 119

Search results

Summary of Contents for Mk1500

Reviews: