manualshive.com logo in svg

Canon Mk1500, User Manual, Page: 104 / 119

Share
Download
Canon Mk1500 User Manual Download Page 104

100

5.4

  Replacing the Cassette

   Replacing the ribbon cassette  

If the message “End of ribbon.” appears while printing is in progress, replace the ribbon cassette as shown 
below. Contact your nearest dealer to purchase replacement ribbon cassettes.

1

  Open the cover.

2

  Detach the ribbon cassette.

Pull the cassette out toward you.

Place the removed ribbon cassette into the plastic bag, then discard it immediately in 
compliance with local regulations regarding the disposal of such items.

•

3

  Take up the slack in the new ribbon.

Remove the stopper and then fix the slack in the ribbon.

The printer cannot detect whether ribbon is present if there is any slack in the ribbon. Be 
sure to take up any slack.

Dispose the removed stopper according to local government regulation.

•

4

  Install the new ribbon cassette.

Push the cassette in all of the way until it clicks into place.

If the ribbon cassette is loose, the ribbon may not be detected, so be sure to press it in until 
it clicks.

•

CAUTION

Do not touch the connector (metal part)

Do not hold the connection terminal (metal part) of the cassette. Doing so could cause an 
improper recognition of the cassette.

5

  Close the cover.

6

 Press 

[Enter].

Printing resumes from the page following the page that was 
interrupted.

•

Summary of Contents for Mk1500
























































































































Reviews:

No comments