manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 84 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 84

Chapter 4  

4-6

4.4 Parts Replacement Procedure

4.4.1 Copyboard glass

4.4.1.1 Removing the Copyboard Glass

0013-1210

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Remove the two screws [1], and then remove the glass holder [2].

2) Slide the copyboard glass [3] to remove it.

F-4-10

Take care not to touch the contact sensor[4] when removing the copyboard

glass [3].

4.4.1.2 Procedure after Replacing the Copyboard Glass 

(equipped with SEND functions)

0013-9588

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

After replacing the copyboard glass, enter the correction values (X, Y, Z) of

the standard white plate which are indicated on the back of the new copy-

board glass in the service mode.

Correction value (X): Service mode>#SCAN>#SCAN NUMERIC>No.213

Correction value (Y): Service mode>#SCAN>#SCAN NUMERIC>No.214

Correction value (Z): Service mode>#SCAN>#SCAN NUMERIC>No.215

Also, rewrite the values on the service label.

F-4-11

4.4.2 Reader Controller PCB

4.4.2.1 Removing the Analog Processor PCB

0013-1211

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

MEMO:

This machine stores adjustment values in the image processor PCB, not the

analog processor PCB.

Accordingly, you need not input adjustment values after replacing the analog

processor PCB.

1) Remove the ADF or copyboard.

2) Remove the copyboard glass, reader rear cover (small), and leader rear

cover.

3) Disconnect all connectors and flexible cables from the analog processor

PCB.

4) Remove the two screws [1], and then remove the analog processor PCB

[2].

F-4-12

4.4.3 Scanner Motor

4.4.3.1 Removing the Reader Motor

0013-1212

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Remove the ADF or copyboard.

2) Remove the reader rear cover (small), reader cover, and rear cover.

3) Remove the reader motor [4] by removing one spring [1], three screws [2],

and one connector [3].

F-4-13

When reinstalling the reader motor, attach the spring [1] with the three

screws [2] fastened temporarily, tighten the circled screw [2] tightly, and fi-

nally tighten the remaining two screws [2] tightly.

4.4.4 Contact sensor

4.4.4.1 Removing the Contact Sensor

0013-1213

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

[1]

[3]

[2]

[4]

  8 2 0 6 8 6 6 7 9 3 4 9

c o r r e c t o n  
va l u e   ( X )

c o r r e c t o n
va l u e   ( Y )

c o r r e c t o n
va l u e   ( Z )

[1]

[2]

[1]

[3]

[4]

[2]

[2]

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments