manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 154 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 154

Chapter 10  

10-2

10.2 Basic Operation

10.2.1 Outline of Operation Mode

0013-1193

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

This machine has 2 operation modes. This machine operates in the operation mode specified by the host machine to perform printing. Operation mode names, brief

outline of operations, and associated print modes are given in the following table:

T-10-2

[1] Forward Pickup/Delivery Operation

The document flows as shown below.

MEMO:

This operation is performed for all single-sided documents irrespective of whether document widths are the same.

F-10-3

Operation mode name

Outline of operation

Associated print mode

[1] Forward pickup/delivery

Picks up, reads, and then delivers an document. Single-sided document >

Simplex printing
Single-sided document >
Duplex printing (This operation
is performed for documents
with the same width.)

[2] Forward feed/reversal 
delivery

Picks up, reads, reverses, and delivers an
document.

Double-sided document >
Duplex printing
Double-sided document >
Simplex printing (This
operation is performed for
documents with the same
width.)

Document

Pickup

Formation of loop

Reading

Delivery

End of job

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments