manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 208 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 208

Chapter 15  

15-2

15.1.2 Using the Mode

0013-1302

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

F-15-1

15.2 Default settings

15.2.1 Service Mode Menus

0013-1303

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

#SSSW
No.

Initial setting

Function

SW01

00100000

error/copy control

SW02

not used

SW03

00000000

echo remedy setting

SW04

00000000

communication fault remedy setting

SW05

00000000

standard function (DIS signal) setting

SW06 - SW11

not used

SW12

00000010

page timer setting

SW13

00000000

meter/inch resolution setting

SW14

00000010

inch/meter resolution setting

SW15 - SW27

not used

SW28

00000000

V.8/V.34 protocol settings

SW29

not used

SW30

00010000

Assigning a New Dial Tone Detection Method 

SW31 - SW33

not used

SW34

00000000

waste toner full display setting

SW31 - SW50

not used

1) Selecting Service Mode
Press the Additionalfunctions
key, 2key, 8key, Additional functions
key sequentially.

#SSSW

# N U M E R I C   P a r a m .

# N U M E R I C   P a r a m .

2) Selecting a Menu Item
Select the Menu item using the
[left arrow]/[right arrow] on the
 touch panel.

3) Press [OK].

5) Registering/Setting Data
Enter data using the keypad, 
and then press [OK].

6) Press the [Stop]/[Additional
 functions]/[Reset] key to end
 the service mode.

# N U M E R I C   P a r a m .

# 3

NUMER I C

P a r am.

0 0 1

0 0 1

0 0 2

0 0 2

0

0

1 0

4) Selecting a Prarameter
Select the Prarameter using the
[left arrow]/[right arrow].

1) Selecting Service Mode
Press the Additionalfunctions
key, 2key, 8key, Additional functions
key sequentially.

#SSSW

3) Selecting a Menu Item
Press [OK].

2) Press [OK] on the 
touch panel.

5) Registering/Setting Data
Enter data using the keypad, 
and press the [OK].

6) Press the [Stop]/[Additional
 functions]/[Reset] key to end
 the service mode.

0 3 3

4) Selecting a Bit Switch
Select the bit using the
[left arrow]/[right arrow] on 
the touch panel.

# S S S W

# S S S W

000000000

000000000

<Operation at the time of Bit SW>

<Operation at the time of Parameter>

0 3 3

# S S S W

000000000

0 3 3

# S S S W

000000001

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments