manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 156 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 156

Chapter 10  

10-4

10.2.2 Document Size Detection

0013-1194

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

This machine detects the original size while feeding the original. (Same-type mixed printing and banner paper printing are included.)

The document feeder tray does not have a sensor for detecting the paper size.

T-10-3

10.2.3 Paper Pickup Operation

0013-1195

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

The pickup unit consists of pickup and transport rollers. When the Start Key signal or Original Feed signal is input, the ADF motor (M2001) turns in the normal

direction and then the pickup solenoid (SL2001) turns on. The pickup unit lowers and the pickup and transport rollers rotate to feed the paper. The shutter moves

up in conjunction with the pickup unit. A separation pad is used to prevent multiple sheets from being fed at the same time.

When the original reaches the registration roller where is it looped, the pickup solenoid (SL2001) turns off and the pickup unit roller rises. Next the registration

solenoid (SL2002) turns on and the original is fed by the registration roller. At this time, the pickup roller drive shaft which is rotated via the spring one-way clutch

is stationary at the highest position in the pickup unit. The pickup roller incorporating a one-way clutch is rotated by the friction against the paper.

F-10-6

10.2.4 Reversal Operation

0013-1196

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

There are two types of reversal operations, reversal from the top side to the reverse side and reversal from the reverse side to the top side. However, since their

operating principles are the same, only reversal from the top side to the reverse side is described below.  

a. When the ADF motor (M2001) turns and the registration solenoid (SL2002) turns on, the registration roller turns to feed the paper along the platen guide for

surface scanning. After completion of scanning, the paper is fed to the delivery unit by the transport roller 1 and delivery roller.

Function

Description

Sensor used (symbol)

Document length detection Detects the document length according to the 

distance from the position where the document edge 
sensor (SR2002) turns on to the position where the 
document edge sensor (SR2002) turns off.

Document edge sensor (SR2002)

ADF motor (M2001)

Pickup solenoid (SL2001)

Shutter

Pickup roller

Ppaer

Feed roller

Separation pad

Shutter

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments