manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 226 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 226

Chapter 15  

15-20

15.6.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)>

0013-1365

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Adjust the position at which horizontal scanning of a document being copied ends (when scanning on a document fed from ADF).  The larger the adjustment value,

the narrower the bottom margin of the image becomes.

15.6.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)>

0013-1366

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Adjust the position at which horizontal scanning of a FAX document scanned in superfine mode ends.  The larger the adjustment value, the narrower the bottom

margin of the image becomes.

15.6.13 <045: Horizontal scan end position correction (fine:scanning on ADF)>

0013-1367

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Adjust the position at which horizontal scanning of a FAX document scanned in fine mode ends.  The larger the adjustment value, the narrower the bottom margin

of the image becomes.

15.6.14 <046: Horizontal scan end position correction (standard:scanning on ADF)>

0013-1369

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Adjust the position at which horizontal scanning of a FAX document set to the standard scan resolution ends.  The larger the adjustment value, the narrower the

bottom margin of the image becomes.

15.6.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)>

0013-1370

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Correct the magnification of vertical scanning of a document fed from the ADF.  The larger the adjustment value, the more the image stretches in the vertical scan-

ning direction.

15.6.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)>

0013-1371

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Correct the magnification of horizontal scanning of a document fed from the ADF.  The smaller the adjustment value, the more the image ruduces in the horizontal

scanning direction.

This menu is used to adjust the ADF feed motor speed. If you changed the adjustment value in this mode, the adjustment value selected for SCAN NUMERIC>54

must also be incremented/decremented by the same amount.

Do not change the adjustment value extremely.

15.6.17 <054: Pickup motor speed correction (when the ADF is used) >

0013-1372

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

This menu is used to adjust the ADF pickup motor speed. If you have adjusted the ADF feed motor speed by selecting SCAN NUMERIC>48, the ADF pickup

motor speed must also be incremented/decremented by the same amount.

Do not change the adjustment value extremely.

15.6.18 <193: ADF special standard-sized paper: LGL misidentification-ready>

0013-1373

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LEGAL").

0: LEGAL

1: FOOLSCAP

2: M_OFFICIO

3: A_FOOLSCAP

4: FOLIO

5: G_LEGAL

6: A_OFFICIO

7: B_OFFICIO

15.6.19 <194: ADF special standard-sized paper: LTR misidentification-ready>

0013-1374

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").

0: LTR

1: G_LTR

2: A_LTR

15.6.20 <195: ADF special standard-sized paper: LTR_R misidentification-ready>

0013-1375

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTRR").

0: LTR_R

1: FOOLSCAP

2: OFFICIO

3: E_OFFICIO

4: G_LTR_R

5: A_LTR_R

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments