Canon ImageRUNNER 1022iF, Service Manual, Page: 197 / 270

Chapter 14
14-1
14.1 Error Code Details
14.1.1 Error Code Details
0013-1429
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
T-14-1
Display
Code Detail Code Main Cause/Symptom Countermeasure
E000 0000 Startup error
The temperature detected by the main or sub thermistor does
not rise to the specified value during startup control.
- Check the fixing film connector.
- Replace the fixing film unit.
- Replace the DC controller PCB.
E001 0000 Abnormally high temperature (detected by main thermistor)
The main thermistor detected an abnormally high temperature
(235 deg C) during temperature control.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
0001 Abnormally high temperature (detected by sub thermistor)
The sub thermistor detected an abnormally high temperature
(300 deg C) during temperature control.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
E002 0000 Low temperature during temperature control.
The target temperature is not reached during temperature
control.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
E003 0000 Abnormally low temperature (detected by main thermistor)
After the temperature detected by the main thermistor has
reached the specified value, it does not reach the specified
value during initial rotation.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
0001 Abnormally low temperature (detected by sub thermistor)
After the temperature detected by the sub thermistor has
reached the specified value, it does not reach the specified
value during initial rotation.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
E010 0000 Main motor failure
The main motor is faulty.
- Check the connector of the main motor.
- Replace the main motor.
- Replace the DC controller PCB.
E019 0000 Waste toner full detection
The waste toner full state was detected.
Replace the drum unit
0001 Waster toner full detection sensor is faulty.
The waste toner full state was detected continuously for five or
more seconds while the main motor was turning.
- Check the connector of the waster toner full sensor.
- Replace the waste toner full sensor.
- Replace the DC controller PCB.
E100 0000 BD detection PCB failure
The BD detection PCB is faulty.
- Check the connector of the BD detection PCB.
- Replace the laser scanner unit.
- Replace the DC controller PCB.
E196 0001 Flash ROM write/read error - Replace the image processor PCB.
The write/read of Flash ROM in the image processor PCB is
faulty.
0002 PCL ROM write/read error - Replace the PCL PCB.
- Replace the image processor PCB.
The write/read of PCL ROM in the image processor PCB is
faulty.
E197 0000 Printer engine communication error
Erroneous communication between the DC controller PCB and
image processor PCB was detected.
- Check the connectors of the DC controller PCB and image
processor PCB.
- Replace the DC controller PCB for normal connection.
- Replace the image processor PCB.
E716 0000 Erroneous communication with optional cassette
Disconnection of the optional cassette was detected after
power-on, detection of normal connection to the optional
cassette, and start of communication.
- Check the connectors of the optional cassette PCB and DC
controller PCB.
- Replace the optional cassette PCB for normal connection.
- Replace the DC controller PCB.
E719 0000 Erroneous communication with card reader (serial communication)
- Disconnection from the card reader has been detected since
communication started after confirmation of normal
connection to the card reader (after power-on).
- A serial communication error has occurred. (The serial
communication error cannot be recovered.)
- Check the connectors of the card reader and image processor
PCB.
- Replace the card reader for normal connection.
- Replace the image processor PCB.
0001 Erroneous communication with coin vendor (serial communication)
- Disconnection from the coin vendor has been detected since
communication started after confirmation of normal
connection to the coin vendor (after power-on).
- A serial communication error has occurred. (The serial
communication error cannot be recovered.)
- Check the connection between the image processor PCB and
serial PCB.
- Check the connectors of the serial PCB and coin vendor for
normal connection.
- Replace the serial PCB.
- Check the coin vendor.
- Replace the image processor PCB.