manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 140 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 140

Chapter 9  

9-4

9.4 Parts Replacement Procedure

9.4.1 External Covers

9.4.1.1 External Covers

9.4.1.1.1 Detaching the Reader Rear Cover (Small)

0013-2399

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Remove the screw [1], and then detach the reader rear cover (small).

F-9-4

9.4.1.1.2 Detaching the Reader Rear Cover

0013-2400

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Open the ADF or copyboard.

2) Detach the reader rear cover (small).

3) Remove the three screws [1], disconnect the three connectors [2], and then

remove the ground wire [3].

4) While pushing the reader rear cover [5] upward with your finger to release

the claw [4], slide the cover backward to remove it.  

F-9-5

9.4.1.1.3 Detaching the Rear Cover

0013-2401

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) To release the hooks at the back of the machine, move the machine

backward until the hooks are about 5 cm away from the edge of the desk

and so on.

2) Remove the screw [1].

3) Release the three claws[2] at the right and the three claws [3] at the top.

4) Release the two claws [4] at the bottom, and then detach the rear cover [5].

[1]

[4]

[5]

[1]

[1]

[3]

[2]

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments