manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 15 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 15

Contents

15.7.2 

Numerin Parameter Settings (Numeric Prama.) ................................................................................................ 15- 23

15.7.2.1 

Numeric Parameter Functional configuration..................................................................................................................... 15- 23

15.7.2.2 

<031: Top registration adjustment (manual feed tray)> ..................................................................................................... 15- 23

15.7.2.3 

<032: Top registration adjustment (cassette)>................................................................................................................... 15- 23

15.7.2.4 

<033: Top registration adjustment (duplex unit)>............................................................................................................... 15- 23

15.7.2.5 

<034: Left-end registration adjustment (manual feed tray)> .............................................................................................. 15- 23

15.7.2.6 

<035: Left-end registration adjustment (cassette 1)>......................................................................................................... 15- 23

15.7.2.7 

<036: Left-end registration adjustment (cassette 2)>......................................................................................................... 15- 23

15.7.2.8 

<039: Left-end registration adjustment (duplex unit)>........................................................................................................ 15- 23

15.7.2.9 

<040: Target fixing temperature adjustment (manual feed tray)> ...................................................................................... 15- 23

15.7.2.10 

<041: Target fixing temperature adjustment (cassette 1)>............................................................................................... 15- 23

15.7.2.11 

<042: Target fixing temperature adjustment (cassette 2)>............................................................................................... 15- 24

15.7.2.12 

<051: Target 2-sided temperature adjustment> ............................................................................................................... 15- 24

15.7.2.13 

<053: Margin adjustment at the leading edge of the copy> ............................................................................................. 15- 24

15.7.2.14 

<054: Margin adjustment at the trailing edge of the copy> .............................................................................................. 15- 24

15.7.2.15 

<055: Margin adjustment at the right edge of the copy> .................................................................................................. 15- 24

15.7.2.16 

<056: Margin adjustment at the left edge of the copy> .................................................................................................... 15- 24

15.8 

Registration of Accessories (ACC) .......................................................................................................15- 25

15.8.1 

Accessory Registration ...................................................................................................................................... 15- 25

15.9 

Display of Counter Information (COUNTER) ........................................................................................15- 25

15.9.1 

Counters ............................................................................................................................................................ 15- 25

15.9.2 

Clearing Counters.............................................................................................................................................. 15- 25

15.10 

Service Report (REPORT) ..................................................................................................................15- 27

15.10.1 

Report Output .................................................................................................................................................. 15- 27

15.10.2 

System Data List.............................................................................................................................................. 15- 27

15.10.3 

System Dump List............................................................................................................................................ 15- 27

15.10.4 

Counter List...................................................................................................................................................... 15- 29

15.10.5 

Error Log List ................................................................................................................................................... 15- 29

15.10.6 

Spec List .......................................................................................................................................................... 15- 31

15.10.7 

Service Label ................................................................................................................................................... 15- 32

15.11 

Download (DOWNLOAD)....................................................................................................................15- 33

15.11.1 

Download ......................................................................................................................................................... 15- 33

15.12 

Initialization of Set Value (CLEAR) .....................................................................................................15- 33

15.12.1 

Clear ................................................................................................................................................................ 15- 33

15.13 

Error Display (ERROR DISPLAY).......................................................................................................15- 33

15.13.1 

Error Display .................................................................................................................................................... 15- 33

15.14 

Display of ROM Information (ROM) ....................................................................................................15- 33

15.14.1 

ROM display .................................................................................................................................................... 15- 33

15.15 

Test Mode (TEST) ..............................................................................................................................15- 34

15.15.1 

D-RAM Test<(1) D-RAM TEST>...................................................................................................................... 15- 34

15.15.2 

Scan Test ((2) SCAN TEST)............................................................................................................................ 15- 34

15.15.3 

Print Test ((3) PRINT TEST)............................................................................................................................ 15- 34

15.15.4 

MODEM Test ((4) MODEM TEST) .................................................................................................................. 15- 35

15.15.5 

FUNCTION TEST <(6) FUNCTION TEST>..................................................................................................... 15- 37

15.15.6 

Roller cleaning mode ((0) ROLLER CLEAN) ................................................................................................... 15- 41

Chapter 16  

Upgrading

16.1 

Outline ....................................................................................................................................................16- 1

16.1.1 

Overview of Upgrade ........................................................................................................................................... 16- 1

16.1.2 

Overview of Service Support Tool ....................................................................................................................... 16- 1

16.2 

Making Preparations ...............................................................................................................................16- 1

16.2.1 

Registering the System Software ........................................................................................................................ 16- 1

16.2.2 

Connection........................................................................................................................................................... 16- 3

16.3 

Downloading System Software ...............................................................................................................16- 4

16.3.1 

Downloading System ........................................................................................................................................... 16- 4

16.3.1.1 

Downloading Procedure....................................................................................................................................................... 16- 4

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments