manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Service Manual, Page: 180 / 270

Share
Download
Canon ImageRUNNER 1022iF Service Manual Download Page 180

Chapter 12  

12-4

F-12-11

1) Load the test chart in the ADF and make a copy of it. 

2) Compare the horizontal registration of the chart with that of the copy. If

required, make an adjustment. 

The specified horizontal registration is 10mm +/-2mm. 

3) Enter the service mode.

Sequentially press the Additional functions key, 2 key, 8 key, and Additional

functions key on the operation panel of the host machine.

4) Using the arrow keys on the operation panel, display "#SCAN".

5) Press the OK key.

6) Using the arrow keys on the operation panel, display "#SCAN

NUMERIC".

7) Press the OK key.

8) Using the arrow keys, select "41".

9) Using the numeric keys, change the value to determine the optimum value.

Next, press the OK key. (Default: 0)

If the registration cannot be set to the specified value using software, use the

following procedure:

1) Open the ADF pickup tray.

2) Loosen the two screws [1] and move the slide guide forward or backward

according to the scale calibrated in mm so that the registration is within

spec.

F-12-12

MEMO:

Making copies with the slide guide shifted 1 mm upward will increase the

right registration (on the upper side of paper) by 1 mm.

12.4.3.3 Leading edge registration adjustment

0013-1280

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Load the test chart in the ADF and make a copy of it. 

2) Compare the end registration of the test chart with that on the copy. If re-

quired, make an adjustment. 

The specified end registration is 10mm +/-2mm.

F-12-13

The image is shifted to the left. -> Decrease the value.

The image is shifted to the right. -> Increase the value.

Unit of adjustment   1 = 0.1 mm

3) Enter the service mode.

Sequentially press the Additional functions key, 2 key, 8 key, and Additional

functions key on the operation panel of the host machine.

4) Using the arrow keys on the operation panel, display "#SCAN".

5) Press the OK key.

6) Using the arrow keys on the operation panel, display "#SCAN

NUMERIC".

7) Press the OK key.

8) Using the arrow keys, select "42".

9) Using the numeric keys, change the value to determine the optimum value.

Next, press the OK key. (Default: 219)

 If the registration cannot be set to the specified value using software,

make adjustments again starting with the perpendicular adjustment. 

Copy of the test sheet

(feeding direction)

10±2mm

[1]

Copy of the test sheet

(feeding direction)

Leading edge margin

L

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Reviews:

No comments