Canon ImageRUNNER 1022iF Service Manual Download Page 238

Page: 238 / 270

Chapter 15

15-32

[9] Option ROM availability

[10] USB memory availability

[11] No. 1/No. 2 paper full sensor sensor availability

[12] USB serial number

[13] MAC address

[14] Backup battery availability

[15] Anlog purocessor PCB version

15.10.7 Service Label

0013-1417

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

Enter the value given in the service label affixed to the rear cover when it has been replaced with a new one.

F-15-11

FACTORY

031

026

032

031

033

032

034

100

033

035

100

034

036

100

041

037

100

042

038

100

043

039

100

044
045
046
047
048
054
213
214
215

#PRINT>#PRINT NUMERIC

#SCAN>#SCAN NUMERIC

body No:BFDxxxxx

#SCAN>#SCAN NUMERIC

Summary of Contents for ImageRUNNER 1022iF















































































































































































































































































Search results

Summary of Contents for ImageRUNNER 1022iF

Reviews:

Canon ImageRUNNER 1022iF, Service Manual, Page: 238 / 270

Search results

Summary of Contents for ImageRUNNER 1022iF

Reviews: