manualshive.com logo in svg

Canon imagePASS-A2, Service Manual

Share
Download
Canon imagePASS-A2 Service Manual Download Page 7

I

NTRODUCTION

7

I

NTRODUCTION

This document includes information about servicing the Canon imagePASS-A2. In this 
document, Canon imagePASS-A2 is referred to as “the imagePASS.”

About the imagePASS

The imagePASS embeds computer connectivity and highly efficient PostScript and PCL 
printing capacity into the Canon imageRUNNER ADVANCE C9200/C7200 series copier.

It allows the customer to use the copier as a PostScript printer and scanner, and it provides 
efficient image processing and printing controls. Once it is connected to the copier through a 
network, customers can print to the imagePASS from supported client computers on the 
network (Windows or Mac, or a UNIX workstation running TCP/IP).

The imagePASS ships with system software installed so that customers can use the imagePASS 
immediately. However, as part of servicing the imagePASS, you may need to reinstall system 
software.

F

IGURE

 1:

The imagePASS

Summary of Contents for imagePASS-A2



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands