manualshive.com logo in svg

Canon imagePASS-A2, Service Manual

Share
Download
Canon imagePASS-A2 Service Manual Download Page 13

S

ERVICE

 P

ROCEDURES

13

General information for servicing the imagePASS

This section includes general information related to most service procedures, including how 
to safely turn the imagePASS on and off, how to remove, open, and close it, and how to use 
the service switches.

Power scheme

The imagePASS has its own power supply and AC power cable. To function, the imagePASS 
must be connected to the copier and to a proper AC power outlet. The imagePASS will not 
start up until the copier is powered on. Powering off the copier powers off the imagePASS as 
well. 

When you power off the copier, the imagePASS takes approximately 3 to 5 minutes to shut 
down and power off. Always check the DIAG LEDs on the connector panel of the 
imagePASS; when the LEDs go out, the imagePASS is off. 

The imagePASS power supply supplies power directly to the motherboard and HDD. 
From the motherboard, power goes to the CPU, UIB board, and chassis fan. 

The imagePASS powers off and on by means of the copier power switch. The imagePASS 
shuts down if it is disconnected from the copier. In normal usage, the customer can leave the 
imagePASS plugged in to the AC power outlet and connected to the copier. 

Before you perform service on the imagePASS hardware:

• Power off the imagePASS using the copier power switch.

• Unplug the imagePASS from the AC power outlet.

• If you plan to open the imagePASS while it is connected to the copier (

not

 

recommended

), 

make sure also to unplug the copier from its AC power outlet before you open the 
imagePASS. 

Shutting down the imagePASS

Before you shut down the imagePASS, review the following information.

• Notifying the network administrator

Before you inspect or service the imagePASS, you must shut it down. Make sure that the 
system is not processing or printing a job. Obtain permission from the network 
administrator to temporarily shut down the imagePASS.

• Forcing the imagePASS to shut down

If the imagePASS is not responding, and it is not possible to shut it down from the copier 
touch panel, you can force the imagePASS to shut down. Only force the imagePASS to 
shut down as a last resort, after an unsuccessful attempt at a normal shutdown.

Summary of Contents for imagePASS-A2



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands