Campbell Hausfeld TL0501, Operating Instructions Manual

Page: 3 / 24

Do not operate or
allow anyone else to
operate the tool if
any warnings or warning labels are
not legible. Warnings or warning
labels are located on the tool
magazine and body.
Do not drop or
throw the tool.
Dropping or throwing the tool can
result in damage that will make
the tool unusable or unsafe. If the
tool has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
Do not exceed
the maximum
operating pressure of the air tool
(90 psi). This can reduce the life of
the tool.
j . Do not exceed any pressure rating
of any component in the system .
Maximum operating pressure
of 90 psi is measured at the tool
inlet while the tool is running .
The pressure drop between the
compressor and tool needs to be
compensated for at the compressor .
k . Do not depress trigger when
connecting the air supply hose .
l . Never trigger the tool when
not applied to a work object .
Attachments must be securely
attached . Loose attachments can
cause serious injury .
Clean and check
all air supply
hoses and fittings before
connecting the tool to an air
supply. Replace any damaged
or worn hoses or fittings. Tool
performance or durability may be
reduced.
sERviCE
a . Tool service must be performed only
by qualified repair personnel.
b . When servicing a tool, use only
identical replacement parts. Use
only authorized parts.
c . Use only the lubricants supplied
with the tool or specified by the
manufacturer.
k . Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges, and refrigerators.
There is
an increased risk of electric shock if
your body is grounded .
l . Explore the workpiece to avoid
contact with hidden wiring.
Thoroughly investigate the
workpiece for possible hidden
wiring before performing work .
Contact with live wiring will shock
the operator .
m . Never point an air tool at oneself
or any other person
. Serious injury
could occur .
n . Do not put hands near or under
moving parts .
Tool UsE anD CaRE
a . Use clamps or another practical way
to secure and support the workpiece
to a stable platform.
Holding the
work by hand or against the body is
unstable and is able to lead to loss
of control .
b . Do not force the tool. Use the
correct tool for the application . The
correct tool will do the job better
and safer at the rate for which the
tool is designed .
c . Do not use the tool if the switch
does not turn the tool on or off.
Any
tool that cannot be controlled with
the switch is dangerous and must be
repaired .
d . Disconnect the
tool from the
air source before making
adjustments, doing tool
maintenance, clearing jams,
leaving work area,loading,
or unloading the tool. Such
precautionary measures reduce the
risk of injury to persons .
e . Store the tool when it is idle out
of reach of children and other
untrained persons.
A tool is
dangerous in the hands of untrained
users .
f . Maintain the tool with care. Keep
a cutting tool sharp and clean . A
properly maintained tool, with sharp
cutting edges reduces the risk of
binding and is easier to control .
g . Check for misalignment or binding
of moving parts, breakage of parts,
and any other condition that affects
the tool’s operation.
If damaged,
have the tool serviced before using .
Many accidents are caused by poorly
maintained tools . There is a risk of
bursting if the tool is damaged .
h . Use only accessories that are
identified by the manufacturer for
the specific tool model.
Use of an
accessory not intended for use with
the specific tool model increases the
risk of injury to persons .
i . Selecting an appropriate tool
actuation system, taking into
consideration the work application
for which the tool is used .
Never
use
gasoline or other
flammable liquids to clean
the tool. Never use the
tool in the presence of flammable
liquids or gases. Vapors could
ignite by a spark and cause an
explosion which will result in death
or serious personal injury.
Release all
pressure from
the system before attempting to
install, service, relocate or perform
any maintenance.
Always disconnect
tool from the
power source when unattended,
performing any maintenance or
repair, clearing a jam, or moving
the tool to a new location.
Always fit tool
with a fitting or
hose coupling on or near the tool in
such a manner that all compressed
air in the tool is discharged at the
time the fitting or hose coupling is
disconnected. Do not use a check
valve or any other fitting which
allows air to remain in the tool.
Death or serious personal injury
could occur.
Never carry the
tool by the air
hose or pull the hose to move the
tool or a compressor. Keep hoses
away from heat, oil and sharp
edges. Replace any hose that is
damaged, weak or worn. Personal
injury or tool damage could occur.
3
Tl0501
important safety instructions
(Continued)
!
WARNING
www.chpower.com