Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 75 | Manualshive

Page: 75 / 88

background image

66

SmartStack SSIM-A2-01/SSIM-A8-01

0006 Lan Emulation Server connection failed.

The connection between the LAN Emulation Client and the LAN Emulation Server
was lost.
Action: Check that the LES is running and that the cable to switch is connected.

0007 Lan Emulation Server BUS ARP failed. <xx>

The LAN Emulation Client got a bad response from the Broadcast and Unknown
Server (BUS).
Action: Check the setup of the BUS.

0008 Lan Emulation Config Server connection setup failed Code

<xx>.

Failed to connect to the LAN Emulation Configuration Server. See also the error
codes for 004.
Action: Check the LAN Emulation Configuration Server configuration.

0009 Lan Emulation Config Server timeout - Retry exhausted.

The LAN Emulation Configuration Server did not answer any of our CONFIG
requests.
Action: Check the LAN Emulation Configuration Server configuration.

000A Lan Emulation Config Server timeout - Retrying.

The LAN Emulation Configuration Server did not answer of our CONFIG request.
This message is only a warning. The LAN Emulation Client will retry the CONFIG
request. If all CONFIG request retrys fails then the LAN Emulation Client will
report the error 0009.

000B Lan Emulation Config Server failed Code : <xx>

The LAN Emulation Configuration Server responded our CONFIG request with an
error code. See description of message 0004 for an description of the error codes.
Action: Depending on the error code.

000C Lan Emulation Config Server reports frame size mismatch!

The maximum frame size reported by the LAN Emulation Configuration Server in
a CONFIG response does not match the maximum frame size used by the LAN
Emulation Client.
Action: Correct the configuration file.

000D Lan Emulation Server Mf VCC timeout!

The LAN Emulation Broadcast and Unknown Server (BUS) has not opened a
connection to the LAN Emulation client within the number of seconds specified by
the JoinTimeout value in the configuration file (the JoinTimeout default value is 5
seconds).

«
...
73
74
75
76
77
...
»

Summary of Contents for SSIM-A2-01

























































































Reviews:

No comments

Related manuals for SSIM-A2-01

Brand: Jetter Pages: 35

Brand: Keithley Pages: 59

Brand: Ubiquiti Pages: 22

Brand: Ublox Pages: 17

Nighthawk M6 Pro

Brand: AT&T Pages: 2

Brand: Ruckus Wireless Pages: 102

Brand: peplink Pages: 2

Brand: Eicon Networks Pages: 32

Brand: H3C Pages: 3

SmartMesh IA-510 D2511

Brand: Dust Networks Pages: 30

Brand: Draytek Pages: 2

Brand: Genie Pages: 6

Brand: X-Micro Pages: 49

Brand: Airlink101 Pages: 13

Brand: ebm-papst Pages: 13

Brand: Patton Pages: 62

Brand: Supermicro Pages: 131

Brand: FiberHome Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands