Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 27 | Manualshive

Page: 27 / 88

background image

18

SmartStack SSIM-A2-01/SSIM-A8-01

Console Configuration

ATM Configuration - Port Menu

To change the configuration of the SSIM-Ax-01 ATM 155 Uplink Module, select
Port Configuration from the Configuration menu and type the port number when
prompted. The following menu is displayed.

The following items are available:

Enabled

Sets the administrative state of the port. Setting Enabled to Yes turns the module
on. Setting Enabled to No turns the port off. Possible values are Yes and No.

Status

Shows the operative status of the port. Up is displayed when the port is running as
configured by the user. Down indicates that the port is not running—either because
Enabled was set to No or because an error has occurred. The information in this
field cannot be edited. Possible values are Up and Down.

Apply Changes

Configuration parameters for the module port can be changed from a console
session or remote telnet session. However, any changes to the port configuration
will not take effect until the port is restarted. Selecting Apply Changes will restart
the port using the new configuration information.

Note that traffic through the port will be disrupted while the port restarts.

«
...
25
26
27
28
29
...
»

Summary of Contents for SSIM-A2-01

























































































Reviews:

No comments

Related manuals for SSIM-A2-01

Brand: D-Link Pages: 99

Brand: D-Link Pages: 5

Brand: D-Link Pages: 15

AirPro DWL-6000AP

Brand: D-Link Pages: 65

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: D-Link Pages: 9

Brand: D-Link Pages: 8

Brand: D-Link Pages: 3

Brand: D-Link Pages: 28

Brand: D-Link Pages: 2

DSL-2540B - ADSL2/2+ Modem With EN Router

Brand: D-Link Pages: 12

Brand: D-Link Pages: 62

Brand: D-Link Pages: 12

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

8677 - BladeCenter Rack-mountable - Power...

Brand: IBM Pages: 126

Brand: Vivotek Pages: 136

Brand: E-TOP Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands