Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 31

Page: 31 / 88

SmartStack SSIM-A2-01/SSIM-A8-01

Console Configuration

ATM Network Advanced Parameters

To view and edit advanced network parameters for the ATM network, select
Advanced Parameters on the ATM Network Setup screen.

The following items are available in the SSCOP section of the screen:

SSCOP

Maximum Receive Window Size

Sets the maximum SSCOP protocol receive window size in bytes.
Possible values: 1 to 16,777,215.
Default: 65,536.

Maximum Connection Control States

Sets the maximum number of transmissions of a BGN, END, ER or RS protocol
data unit.
Possible values: 1 to 255.
Default: 4.

Maximum Poll Data States

Sets the maximum number of data packet transmissions between polls.
Possible values: 1 to 255.
Default: 4.

Summary of Contents for SSIM-A2-01

























































































Search results

Summary of Contents for SSIM-A2-01

Reviews:

Related manuals for SSIM-A2-01

Brands by name

Popular brands

Cabletron Systems SSIM-A2-01, Installation And User Manual

Search results

Summary of Contents for SSIM-A2-01

Reviews:

Related manuals for SSIM-A2-01

Brands by name

Popular brands