manualshive.com logo in svg

Cabletron Systems SSIM-A2-01, Installation And User Manual, Page: 63 / 88

Share
Download
Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 63

54

SmartStack SSIM-A2-01/SSIM-A8-01  

Statistics

Response Code

The status code from the last failed Configure response or Join response. Failed 
responses are those for which the LE_CONFIGURE_RESPONSE or 
LE_JOIN_RESPONSE frame contains a failure code, or fails to arrive within a 
timeout period. If none of the client’s requests have failed, this field has the value 
None. If the failed response contained a STATUS code that is not defined in the 
LAN Emulation specification, this field has the value undefinedError. Possible 
values are None, timeout, undefinedError, versionNotSupported, 
invalidRequestParameters, duplicateLanDestination, duplicateAtmAddress, 
insufficientResources, accessDenied, invalidRequesterId, invalidLanDestination, 
invalidAtmAddress, noConfiguration, leConfigureError and 
insufficientInformation.

IF State

The state the client was in when it updated the Response Code. If the Response 
Code is None, the IF State is Initial State.

Summary of Contents for SSIM-A2-01

























































































Reviews:

No comments