Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 74 | Manualshive

Page: 74 / 88

background image

65

SmartStack SSIM-A2-01/SSIM-A8-01

Appendix B. Log Messages

Error messages that can appear on the console screen are listed below. Following
each message is a short explanation of the message and, where appropriate, steps
that can be taken to resolve the error condition.

0001 Lan Emulation Server join timeout - Retrying!

The LAN Emulation Server did not answer of our JOIN request. This message is
only a warning. The LAN Emulation Client will retry the JOIN request. If all JOIN
request retrys fails then the LAN Emulation Client will report the error 0002.

0002 Lan Emulation Server join timeout - Retry exhausted!

The LAN Emulation Server did not answer any of our JOIN requests.
Action: Check the LAN Emulation Server configuration.

0003 Lan Emulation Server reports frame size mismatch!

The maximum frame size reported by the LAN Emulation Server in a JOIN
response does not match the maximum frame size used by the LAN Emulation
Client.
Action: Correct configuration of MaxDataFrameSize.

0004 Lan Emulation Server join failed Code : <xx>(hex)

The LAN Emulation Server responded our JOIN request with an error code. The
following error codes (decimal) are defined:
1. Invalid Version.
2. Invalid Parameters.
4. Duplicate LAN Address.
5. Duplicate ATM Address.
6. No Resources.
7. Access Denied.
8. Invalid LEC ID.
9. Invalid LAN Destination.
10. Invalid ATM Address.
20. No Configuration.
21. LeCsError.
22. Insufficient Information.
Action: Depending on the error code.

0005 Lan Emulation Server joined successfully!

Information message: The LAN Emulation Client has joined the LES successfully.

«
...
72
73
74
75
76
...
»

Summary of Contents for SSIM-A2-01

























































































Reviews:

No comments

Related manuals for SSIM-A2-01

EtherLink 3C509B

Brand: 3Com Pages: 8

Brand: 3Com Pages: 8

Brand: Enginko Pages: 19

Brand: Quectel Pages: 23

Brand: Bridgeworks Pages: 18

DHI-NVR2104-P-4KS2

Brand: Dahua Pages: 23

Brand: Aztech Pages: 2

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Brand: ProCurve Pages: 2

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Brand: Intel Pages: 86

Brand: Avaya Pages: 73

FlexNetwork 5130 Series

Brand: HPE Pages: 33

Brand: CalAmp Pages: 115

Brand: FOR-A Pages: 2

HHM Series HHM2409

Brand: TDK Pages: 2

Brand: INNOSILICON Pages: 11

Brand: NZXT Pages: 2

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands