Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 34 | Manualshive

Page: 34 / 88

background image

25

SmartStack SSIM-A2-01/SSIM-A8-01

Console Configuration

T316

The maximum time to wait for response to RESTART.
Possible values: 1 to 255.
Default: 120.

T317

The maximum time to act on RESTART. The value set should be less than T316.
Possible values: 1 to 255.
Default: 60.

T322

The maximum time to wait for response to STATUS ENQUIRY.
Possible values: 1 to 255.
Default: 4.

These values correspond to the standard values used on ordinary Token-Ring ports.
Actually, slightly larger frame sizes are allowed to accommodate the frame sizes
defined by the ATM Forum LAN Emulation standard.

The following table shows the configured and actual frame size, as well as the
corresponding largest frame size bits that are used in explorer RIF expansion:

MTU

Configured

TR-LANE

Max Data

frame size

LF bits

1500

1516

001

4472

4544

011

8144

9234

100

17800

18190

110

Table 5. Configured and Actual Frame Size

«
...
32
33
34
35
36
...
»

Summary of Contents for SSIM-A2-01

























































































Reviews:

No comments

Related manuals for SSIM-A2-01

Brand: Patton electronics Pages: 2

Brand: National Instruments Pages: 26

Brand: National Instruments Pages: 85

Module SCXI-1503

Brand: National Instruments Pages: 79

Brand: Patton electronics Pages: 12

Brand: Juniper Pages: 7

Brand: Glacier Pages: 2

Brand: Intel Pages: 26

MMAC-Plus 9G536-04

Brand: Cabletron Systems Pages: 42

Brand: mikroElektronika Pages: 2

Brand: ICOP Technology Pages: 34

IE-SW-PL09M-5GC-4GT

Brand: Weidmuller Pages: 15

Brand: JETWAY Pages: 47

Brand: SMC Networks Pages: 56

Brand: ICS ELECTRONICS Pages: 4

Brand: Lanner Pages: 99

Brand: CyberResearch Pages: 59

Brand: LevelOne Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands