manualshive.com logo in svg

Cabletron Systems SSIM-A2-01, Installation And User Manual, Page: 57 / 88

Share
Download
Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 57

48

SmartStack SSIM-A2-01/SSIM-A8-01  

Statistics

Frame-Forwarding Statistics

The Frame Forwarding Statistics screen provides statistics for traffic received on 
the ATM network for a particular ELAN. All statistics shown are for this VAP.

Bytes Received

The total number of bytes received on this VAP from the ATM network.

Bytes Transmitted

The total number of bytes transmitted on this VAP to the ATM network.

Bytes Forwarded

The total number of bytes forwarded from ATM to other switch ports.

ARP Requests Rx

The number of LE_ARP_REQUESTs received from the ATM network by the 
LEC. Requests may arrive on the Control Direct VCC or on the Control Distribute 
VCC, depending on how the LES is implemented and the opportunity it has had for 
learning. This counter covers both VCCs.

ARP Requests Tx

The number of LE_ARP_REQUESTs sent by the LEC to the ATM network.

Summary of Contents for SSIM-A2-01

























































































Reviews:

No comments