Cabletron Systems SSIM-A2-01 Installation And User Manual Download Page 52 | Manualshive

Page: 52 / 88

background image

43

SmartStack SSIM-A2-01/SSIM-A8-01

Statistics

Port Status

To access the port status screen, select Port Status from the Statistics menu. The
SSIM-Ax-01 ATM 155 Uplink Module will be listed as port 21 or port 25. A
sample screen is shown below.

Port

Shows the port number of the port, used to identify the port on the system.

TrCRF

Shows the name of the CRF that the port or VAP belongs to.

TrBRF

Shows the name of the BRF that the port or VAP belongs to.

Enabled/Ins

For Ordinary Token-Ring ports, this is the enabled and inserted status. This does
not apply to VAPs on an ATM port. Instead the current state at the VAP is
displayed. Please refer to the description of ATM LEC ( VAP) Configuration for
details.

Spd

Shows the operating speed of the port or VAP in megabits per second.

«
...
50
51
52
53
54
...
»

Summary of Contents for SSIM-A2-01

























































































Reviews:

No comments

Related manuals for SSIM-A2-01

Brand: Hal Communications Pages: 25

Brand: Harman Kardon Pages: 66

Brand: IEI Technology Pages: 187

Brand: IEI Technology Pages: 71

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Brand: Paradyne Pages: 2

Brand: Watchguard Pages: 24

Brand: Tripp Lite Pages: 20

ZyXEL EES-1024AF

Brand: ZyXEL Communications Pages: 99

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: FONESTAR Pages: 8

Brand: Zonet Pages: 53

Low Power Series

Brand: FabiaTech Pages: 77

Brand: Cowfish Technologies Pages: 38

Brand: Galaxy Pages: 30

RocketCache 3240X8

Brand: HighPoint Pages: 17

PSoC 4 S Series

Brand: Cypress Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands