Chapter 7 AWARD BIOS SETUP
7-1 BIOS
Instructions
Award’s ROM BIOS provides a built-in Setup program, which allows user to
modify the basic system configuration and hardware parameters. The
modified data will be stored in a battery-backed CMOS, so that data will be
retained even when the power is turned off. In general, the information
saved in the CMOS RAM will stay unchanged unless there is a configuration
change in the system, such as hard drive replacement or a device is added.
It is possible for the CMOS battery to fail, this will cause data loss in the
CMOS only. If this does happen you will need to reconfigure your BIOS
settings.
7-2 Main
Menu
Once you enter the AwardBIOS™ CMOS Setup Utility, the Main Menu will
appear on the screen. The Main Menu allows you to select from several
setup functions and two exit choices. Use the arrow keys to select among
the items and press <Enter> to accept and enter the sub-menu.
CMOS Setup Utility - Copyright © 1984 - 2001
Standard CMOS Feature
Advanced BIOS Feature
Advanced Chipset Feature
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Frequency/Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
Esc: Quit
↑
↓
←
→
: Select Item
F6: Save CMOS To BIOS F7: Load
CMOS From BIOS
F10: Save & Exit Setup
Time, Date, Hard Disk Type….
15” Panel PC User’s Manual
P27
area. Using the measurement circuit illustrated in diagram 6-1 below,
take the gauge value when the voltage value 4.5V or greater as the
pressure load value.
6.2 Surface Hardness : 2H or Higher JIS-K5400
7. Optical Specifications
7.1 Light Transmittance (Total Transmittance)
：
More than 78%
（
Measuring
apparatus
：
Haze meter-made by BYK-Gardner
Type
：
Haze–Gard-plus 4726 Illuminant
：
CIE-A Standard
：
ASTM D 1003
）
8. Reliability Item No. Item Ratings Test Methods & Condition
8.1 Line drawing operation 1,000,000 times of drawing Requirement in
paragraph 5 and 6 Drawing must occur in following manner at any point
within an Action area.
1) Testing equipment
：
Pen plotter
2) Testing load / force
：
2.5 N
3) Sliding speed
：
200 mm / second
4) Tip probe
：
Polyester Pen as defined in sub-paragraph 4-3
（
1
）
8.2 Pen hitting operation 5,000,000 hits with a pen Requirement in
paragraph 5 and 6 Hits must be made in the following manner at any
point within at effective area.
1) Testing equipment
：
Pen plotter
2) Testing load
：
2.5 N
3) Press speed
：
3 hits / second
4) Tip probe
：
Polyester Pen as defined in sub-paragraph 4-3 (1)
9. Environment Durability Performance Item No. Item Ratings Test Methods
& Condition
9.1 High Temperature Test Requirement in paragraph 5 and 6: Put it in a
vessel at the condition of 70 ±1 and 45 ±1% humidity relative for 120
hours. Moreover let it alone for 24 hours or more in a room temperature
and measure it.
9.2 Low Temperature Test Requirement in paragraph 5 and 6: Put it in a
vessel at the condition of –30 ±1 for 120 hours. Moreover, let it alone for
24 hours or more in a room temperature and measure it.
9.3 Humidity Test Requirement in paragraph 5 and 6: Leave in an
environment of 60 ±1 and 90±1% relative humility for 120 hours and
then perform measurements after leaving at room temperature for 24
hours
9.4 Thermal Shock Test Requirement in paragraph 5 and 6: Put it in a
vessel at the condition of 70 ±1 for 30 minutes and then –30 ±1 for
30minutes and his process is repeated by 10cycles. Moreover let it
P30
15” Panel PC User’s Manual
