Buderus Logamatic EMS Operating Instructions Manual Download Page 5 | Manualshive

Page: 5 / 60

background image

Logamatic EMS RC35 user interface - Subject to technical modifications.

5

Explanation of symbols and safety instructions

1

1

Explanation of symbols and safety instructions

1.1

Explanation of symbols

Warnings

Signal words at the beginning of a warning are used to indicate the type and seriousness of the
ensuing risk if measures for minimizing damage are not taken.

•

NOTE

indicates that damage to property may occur.

•

CAUTION

indicates possible minor to medium personal injury.

•

WARNING

indicates possible severe personal injury.

•

DANGER

indicates that severe personal injury may occur.

Important Information

Additional symbols

Warnings in the text are indicated by a warning triangle with a gray background
in a framed box.

In case of danger due to current, the exclamation point on the warning triangle is
replaced with a lightning symbol.

Important information that presents no risk to people or property is indicated with this
symbol. They are separated by lines above and below the text.

Symbol

Explanation

B

Sequence of steps

Æ

Cross-reference to other points in this document or to other documents

•

Listing/list entry

–

Listing/list entry (2nd level))

Tab. 1

«
...
3
4
5
6
7
...
»

Summary of Contents for Logamatic EMS





























































Reviews:

No comments

Related manuals for Logamatic EMS

Brand: Lawler Pages: 5

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: Harmonic Drive Pages: 85

Brand: VAT Pages: 26

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

Brand: Reliance Foundry Pages: 3

Brand: Wesa Pages: 8

Brand: Technische Alternative Pages: 68

Brand: mikroElektronika Pages: 3

Brand: Window Master Pages: 7

Ambience Control 1

Brand: EuroLite Pages: 20

Brand: SKF Pages: 88

Brand: Bentel Pages: 88

Brand: Zenith Pages: 20

Brand: ADLINK Technology Pages: 37

Samos Pro Compact SP-COP2

Brand: Wieland Pages: 36

Brand: C&C Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands