Buderus Logamatic EMS Operating Instructions Manual Download Page 6

Page: 6 / 60

Explanation of symbols and safety instructions

Logamatic EMS RC35 user interface - Subject to technical modifications.

Display text:

Words appearing on the display are shown in

bold

in the text.

Example:

USER MENU

Action sequences:

Sequences of steps are marked with a triangle with its point towards the text.

Example:

Press

If action sequences have more than two steps and the order of the steps is important,
they are numbered (1., 2., ...).

Note on using this manual:

Section 5.1 "Introduction to the User menu" explains in

detail the steps needed for programming all the settings in the Service menu. In the
sections which come after it, programming is only exexplained in outline.

USER MENU

standard display

modes of operation
program
WWSD temperature

Summary of Contents for Logamatic EMS





























































Search results

Summary of Contents for Logamatic EMS

Reviews:

Related manuals for Logamatic EMS

Brands by name

Popular brands

Buderus Logamatic EMS, Operating Instructions Manual

Search results

Summary of Contents for Logamatic EMS

Reviews:

Related manuals for Logamatic EMS

Brands by name

Popular brands