Buderus Logamatic EMS Operating Instructions Manual Download Page 21 | Manualshive

Page: 21 / 60

background image

Logamatic EMS RC35 user interface - Subject to technical modifications.

21

Basic operation

4

Chart displays in the Info menu (outdoor temperature fluctuation and solar yield)

The Info menu gives you the option of viewing graphs showing the fluctuation in outdoor
temperature over the past two days and (if solar components are installed) the solar gyield. This way
you have a clear overview allowing easy comparison of the relevant values.

Outdoor temperature curve (weather station)

The temperature variation over the current and previous day is shown across two screens.
The minimum and maximum values since midnight on the previous day are also shown.

Solar yield

1)

The solar yield display tells you how much the solar collector has contributed to domestic hot water
heating. This is determined using the difference in temperature between the storage tank and the
solar collector, together with the modulation of the solar pump.

The solar yield is highly dependent on the installed system and its components and therefore cannot
be expressed as a value in kWh. This means that the value displayed is a variable specific to this
particular system, which cannot be easily compared with other solar heating systems. However it is
suitable for comparing the yield on different days.

This information is displayed as a graph for the previous and current day.
The solar gain per day and also the weekly total is listed in a table:

SOLAR YIELD THIS WEEK

and also for the previous week:

SOLAR YIELD LAST WEEK

.

In both cases the current day is indicated by a flashing dot. This value is
updated every 15 minutes (also in the graph for the “current day”) and
the total is saved at 12:00 h (midnight) as the value for the relevant day.
The daily values for the current week (Mo-Su) are also added up every
15 minutes.

The days in the current week which still have not passed are marked with
“

---

”. At days where the solar yield could not be determined “

0

” is

displayed.

Both graphs are updated every 15 minutes and a new graph is started at 12:00 am
(00:00) (midnight). Consequently, there will be no display available for the current day
between 12:00 am and 12:14 am (00:00 and 00:14). The minimum and maximum
values are updated progressively.

1) This function depends on the boiler in use.

SOLAR YIELD THIS WEEK

Mo: 10 Fr: ---
Tu: 115 Sa: ---
We: 53 Su: ---
Th: --- Mo-Su: 178

SOLAR YIELD LAST WEEK

Mo: 10 Fr: 75
Tu: 0 Sa: 102
We: 15 Su: 125
Th: 0 Mo-Su: 327

«
...
19
20
21
22
23
...
»

Summary of Contents for Logamatic EMS





























































Reviews:

No comments

Related manuals for Logamatic EMS

ControlMaster CM15

Brand: ABB Pages: 28

Brand: ABATEC Pages: 8

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: Mackie Pages: 16

Brand: TANDBERG Pages: 47

Red Atom PETRA01

Brand: Perenio Pages: 24

Brand: DeLaval Pages: 102

Brand: DSC Pages: 16

Saxun Mosquito Screen Lateral Door 2020

Brand: Gimenez Ganga Pages: 2

Brand: Keysight Technologies Pages: 78

Brand: LOGICDATA Pages: 23

Brand: Carel Pages: 2

Brand: KWC Pages: 8

Arteor 5 742 74

Brand: LEGRAND Pages: 2

Brand: National Instruments Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands