Buderus Logamatic EMS Operating Instructions Manual Download Page 22 | Manualshive

Page: 22 / 60

background image

Basic operation

Logamatic EMS RC35 user interface - Subject to technical modifications.

22

4

4.10 Messages on the display

The controls will display a message if, for example, a particular setting is
not available under current circumstances.

When the display shows “

continue with any key

”:

B

Press any of the buttons to confirm and close the message.

4.11 Shut-down/switching OFF

The RC35 user interface is supplied with power via the heating system and is permanently switched
on. It is only switched off if the heating system is switched off, such as for maintenance purposes.

B

To switch the heating system on or off: set the ON / OFF switch on the boiler to position

1

(ON)

or

0

(OFF).

After switching the unit OFF or in the event of a power failure, the date and time are
retained for up to 8 hours. All other settings are retained permanently.

continue with any key

«
...
20
21
22
23
24
...
»

Summary of Contents for Logamatic EMS





























































Reviews:

No comments

Related manuals for Logamatic EMS

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

Brand: Dantherm Pages: 20

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

OPTISWITCH 5100 C

Brand: KROHNE Pages: 40

nERGY bluePRINT ENGCP15001

Brand: Soundoff Signal Pages: 5

Brand: Conductrix Wampfler Pages: 23

Brand: Carel Pages: 2

Brand: Timotion Pages: 9

Brand: Consort Pages: 4

Brand: Chamberlain Pages: 4

Brand: Shimaden Pages: 16

Brand: Paradox Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands