manualshive.com logo in svg

Brother DCP-8040, Service Manual, Page: 57 / 367

Share
Download
Brother DCP-8040 Service Manual Download Page 57

CHAPTER 2 INSTALLATION AND BASIC OPERATION 

 

2-26

3.2.8 

For Network Interface Cable Users (For Mac

®

 OS X 10.1/10.2.1 or greater Users) 

(1)  Switch off and unplug the machine from the AC outlet and disconnect it from your 

Macintosh if you already connected an interface cable. 

(2)  Turn on your Macintosh

®

. 

(3)  Insert the supplied CD-ROM for the operating system you are using into your CD-ROM 

drive. 

(4) Double-click the 

Start Here OS X 

folder to install the printer driver and Remote Setup 

program. If the language screen appears, select your language. 

(5) Click 

MFL-Pro Suite 

to install. 

(6)  Connect the network interface cable to the printer, and then connect it to a free port on 

your hub. 

(7)  Turn on the machine by plugging in the power cord. Turn the power switch on. 

(8) Select 

Applications 

from the 

Go 

menu. 

(9) Open the 

Utilities 

folder. 

(10) Open the 

Print Center 

icon. 

(11) Click the 

Add Printer... 

button.. 

(12) Select 

AppleTal

k. 

(13) Select 

BRN_xxxxxx_P1

, and then click the 

Add 

button. 

NOTE: 

xxxxxx are the last six digits of the Ethernet address. 

(14) Select 

Quit Printer Center 

from the 

Printer Center 

menu. 

OK: 

The setup is now complete. 

 

NOTE: 

For Mac

®

OS 10.2.1 or greater Users Only Please visit http://solutions.brother.com/ for 

information about using Rendezvous. 

 

 

 

 

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments