manualshive.com logo in svg

Brother DCP-8040, Service Manual, Page: 272 / 367

Share
Download
Brother DCP-8040 Service Manual Download Page 272

CHAPTER 7 MAINTENANCE MODE 

 

7-2

2.     LIST OF MAINTENANCE–MODE FUNCTIONS 

Maintenance-mode Functions 

Function 

Code 

Function 

Reference

Subsection

(Page) 

01 

EEPROM Parameter Initialization 

3.1 (7-4) 

02  

 

03  

 

04  

 

05 

Printout of Scanning Compensation Data 

3.2 (7-5) 

06 

Placement of CCD Unit in Position for Transportation

 

3.3 (7-7) 

07  

 

08 

ADF* Performance Test 

3.4 (7-7) 

09 

Test Pattern 1 

3.5 (7-8) 

10 

Firmware Switch Setting 

3.6.1 (7-9)

11 

Printout of Firmware Switch Data 

3.6.2 (7-11)

12 

Operational Check of LCD 

3.7 (7-12) 

13 

Operational Check of Control Panel PCB 

3.8 (7-13) 

14  

 

15  

 

 

 

 

32 

Sensor Operational Check 

3.9 (7-14) 

53 

Received Data Transfer Function

 

3.10 (7-16)

54 

Fine Adjustment of Scan Start/End Positions

 

3.11 (7-18)

55 

CCD Scanner Area Setting 

3.12 (7-20)

74 EEPROM 

Customizing 

3.13 (7-21)

77 

Printing out of Machine Log Information

 

3.14 (7-22)

80 

Display of the Equipment's Log Information 

3.15 (7-24)

82 

Machine Error Code Indication 

3.16 (7-26)

87 

Output of Transmission Log to the Telephone Line 

3.17 (7-26)

91 

EEPROM Parameter Initialization 

3.1 (7-4) 

99 

Exit from the Maintenance Mode 

 

Cancellation of the Memory Security Mode 
(No applicable to the Japanese version) 

3.18 (7-27)

* ADF: Automatic document feeder

 

Summary of Contents for DCP-8040
















































































































































































































































































































































































Reviews:

No comments