Brother ArtCity140 Service Manual Download Page 5

Page: 5 / 151

Main motor unit ................................................................................................2 - 40

Attachment of Motor 3P supply assy ...............................................................................................2 - 41
Attachment of LED lamp assy .........................................................................................................2 - 42

Main frame and Covers ...................................................................................2 - 43

Attachment of Rear cover assy and Base plate L/R .........................................................................2 - 44
Attachment of Face plate assy and Front cover assy .......................................................................2 - 46

3. Application of Disassembly/Assembly .............................................3 - 1

Disassembly

Main frame and Covers .....................................................................................3 - 2

Disassembly of Face plate assy  .........................................................................................................3 - 3
Disassembly of Rear cover assy  ........................................................................................................3 - 4
Disassembly of Base plate L/R  ..........................................................................................................3 - 5

Main motor unit ..................................................................................................3 - 6

Disassembly of Motor 3P supply assy ...............................................................................................3 - 7

Feed unit ............................................................................................................3 - 8

Disassembly of Tension pulley assy  ..................................................................................................3 - 9
Disassembly of Lower shaft B assy  .................................................................................................3 - 10
Disassembly of Feed module  ...........................................................................................................3 - 11

Needle threading mechanism ..........................................................................3 - 19

Disassembly of Thread tension dial assembly .................................................................................3 - 20

Pattern selecting mechanism ...........................................................................3 - 21

Disassembly of Pattern selecting unit assy ......................................................................................3 - 22

Bobbin winder, Upper shaft, Needle-Presser module ......................................3 - 23

Disassembly of Bobbin winder assy ................................................................................................3 - 24
Disassembly of Upper shaft assy .....................................................................................................3 - 25
Disassembly of Needle-presser module ...........................................................................................3 - 26

Assembly

Bobbin winder, Upper shaft, Needle-Presser module ......................................3 - 30

Pattern selecting mechanism ...........................................................................3 - 38

Lubrication .......................................................................................................................................3 - 39
Assembly of Pattern selecting unit assy ..........................................................................................3 - 40

Needle threading mechanism ..........................................................................3 - 41

Assembly of Thread tension dial assembly .....................................................................................3 - 42

Feed unit ..........................................................................................................3 - 43

Main motor unit ................................................................................................3 - 55

Assembly of Motor 3P supply assy .................................................................................................3 - 56

Summary of Contents for ArtCity140
























































































































































Search results

Summary of Contents for ArtCity140

Reviews:

Related manuals for ArtCity140

Brands by name

Popular brands

Brother ArtCity140, Service Manual

Search results

Summary of Contents for ArtCity140

Reviews:

Related manuals for ArtCity140

Brands by name

Popular brands