Brother ArtCity140 Service Manual Download Page 6

Page: 6 / 151

iii

Main frame and Covers ...................................................................................3 - 57

Assembly of Base plate L/R ............................................................................................................3 - 58
Assembly of Rear cover assy ...........................................................................................................3 - 59
Assembly of Face plate assy ............................................................................................................3 - 60

4. Adjustment ..........................................................................................4 - 1

Removal of covers .............................................................................................4 - 2

Needle point damage .........................................................................................4 - 4

Timing belt tension .............................................................................................4 - 5

Motor belt tension ..............................................................................................4 - 6

Needle plate holder assy position ......................................................................4 - 7

Presser foot hole / Needle plate hole position (front/back) ................................4 - 8

Needle swing timing ...........................................................................................4 - 9

Three point needle drop ...................................................................................4 - 10

Needle interference left/right ............................................................................4 - 11

Needle bar rising ..............................................................................................4 - 12

Needle bar height ............................................................................................4 - 14

Needle clearance .............................................................................................4 - 15

Left straight stitch needle drop and
zigzag stitch maximum left needle drop position .............................................4 - 16

Feed dog position (front/back and left/right) ....................................................4 - 18

Feed dog height ...............................................................................................4 - 19

Upper thread tension .......................................................................................4 - 20

Left and right stitch of buttonhole stitch length ................................................4 - 22

Bobbin winder ..................................................................................................4 - 25

Lower thread tension .......................................................................................4 - 26

5. Failure Investigation for Electronic Parts .........................................5 - 1

Sewing lamp does not light ................................................................................5 - 2

Main motor does not turn or Rotation speed is slow ..........................................5 - 3

6. Special Instructions of Wiring ...........................................................6 - 1

Motor 3P supply assy ........................................................................................6 - 2

LED lead wire ....................................................................................................6 - 3

Summary of Contents for ArtCity140
























































































































































Search results

Summary of Contents for ArtCity140

Reviews:

Related manuals for ArtCity140

Brands by name

Popular brands

Brother ArtCity140, Service Manual

Search results

Summary of Contents for ArtCity140

Reviews:

Related manuals for ArtCity140

Brands by name

Popular brands