Brother ArtCity140 Service Manual Download Page 128

Page: 128 / 151

4 - 10

Adjust

ment

Adjustment

Adjustment

Three point needle drop

[Standard]

At pattern selecting dial [4] (zigzag stitch/stitch width: maximum), the left and right
needle drop position should be the same to the center of the needle hole.

[Adjustment]

1. Turn off the power, and then remove the foot controller.

2. Remove the face plate assy and the pattern selecting dial, and remove the front cover

assy and the rear cover assy.

3. Remove the presser foot.

4. Attach the size 90/14 needle.

5. Attach the pattern selecting dial.

6. Turn the pattern selecting dial until the [4] is the topmost position.

7. Turn the pulley by hand until the needle point comes to the needle plate surface. (Needle bar is left side.)

8. Loosen the screw of the zigzag adjusting nut.

9. Adjust the left/right needle drop position so that the same to the center of the needle hole by turning the zigzag

adjusting nut with a spanner.

*Key point

• Adjust it within the range where the large side of the eccentric amount of the zigzag adjusting nut is upper side.

10. Tighten the screw of the zigzag adjusting nut to secure the zigzag adjusting nut.

*Key point

• When tightening the screw of the zigzag adjusting nut, keep the zigzag adjusting nut from moving.

Pulley

Needle bar

Needle plate

Needle

Pattern
selecting dial

Screw, Pan M3X10

Right needle drop point

Needle

Needle hole of
needle plate

Left needle drop point

Zigzag
adjusting nut

Screw

Screwdriver

Screw

Zigzag adjusting nut

Adjusting range

a = b

Summary of Contents for ArtCity140
























































































































































Search results

Summary of Contents for ArtCity140

Reviews:

Related manuals for ArtCity140

Brands by name

Popular brands

Brother ArtCity140, Service Manual

Search results

Summary of Contents for ArtCity140

Reviews:

Related manuals for ArtCity140

Brands by name

Popular brands