BR-Automation Automation PC 820 User Manual Download Page 216

Page: 216 / 252

216

Maintenance / Servicing • Changing the fan

Automation PC 820 User's Manual V 1.00

2. Changing the fan

•

Cut off power supply to the Automation PC 820 (disconnect from the ACOPOSmulti rail).

•

Touch the housing or ground connection (not the power supply!) in order to discharge any
electrostatic charge from your body.

•

Remove the fan from the holder. To do this, simply press the snap arms inward and
carefully remove the fan from the housing.

•

Disconnect the fan cable and remove the fan.

•

Install the replacement fan in reverse order.

Figure 87: Removing the fan

Figure 88: Disconnecting the fan cable

Summary of Contents for Automation PC 820





























































































































































































































































Search results

Summary of Contents for Automation PC 820

Reviews:

BR-Automation Automation PC 820, User Manual, Page: 216 / 252

Search results

Summary of Contents for Automation PC 820

Reviews: