manualshive.com logo in svg

BR-Automation Automation PC 820, User Manual, Page: 137 / 252

Share
Download
BR-Automation Automation PC 820 User Manual Download Page 137

Software • BIOS options

Ch

apte

r 4

Soft

w

are

137

Automation PC 820 User's Manual V 1.00

1.10.1  Main

1.10.2  Advanced

ACPI Configuration

PCI Configuration

Setting / View

Profile 0

Profile 3

My setting

System time

-

-

System date

-

-

BIOS ID

-

-

Processor

-

-

CPU frequency

-

-

System memory

-

-

Product revision

-

-

Serial number

-

-

BC Firmware rev.

-

-

MAC Address (ETH1)

-

-

Boot counter

-

-

Running time

-

-

Table 91: 945GME Main profile setting overview

Setting / View

Profile 0

Profile 3

My setting

ACPI Aware O/S

Yes

Yes

ACPI Version Features

ACPI v2.0

ACPI v2.0

ACPI APIC support

Enabled

Enabled

Suspend mode

S1 (POS)

S1 (POS)

USB Device Wakeup from 
S3/S4

Disabled

Disabled

Active cooling trip point

Disabled

Disabled

Passive cooling trip point

Disabled

Disabled

Critical trip point

105°C

105°C

Table 92: 945GME Advanced - ACPI configuration profile setting overview

Setting / View

Profile 0

Profile 3

My setting

Plug & Play O/S

No

Yes

PCI latency timer

64

64

Allocate IRQ to PCI VGA

Yes

Yes

Allocate IRQ to SMBUS HC

Yes

Yes

Table 93: 945GME Advanced - PCI configuration profile setting overview

Summary of Contents for Automation PC 820





























































































































































































































































Reviews:

No comments