manualshive.com logo in svg

Blackrock Microsystems NeuroPort, Instructions For Use Manual

Share
Download
Blackrock Microsystems NeuroPort Instructions For Use Manual Download Page 32

 
 
 
 

Revision 1.00 / LB-1070 – NeuroPort Biopotential Signal Processing System IFU 
© 2021 Blackrock Microsystems, LLC 
 

32 

Analog Output 

Analog output properties are accessed from the left side bar of the Hardware 

Configuration window and allows the user to set the properties of the analog 

output ports.  Analog outputs can function as monitor channels, directly mirroring 

signals of interest, or as waveform generators. Each modality has output and 

triggering parameters defined below. 

Label

: User-defined channel label. 

Function

: Assigns the analog channel function.  

Analog Output: Continuous Monitor 

An analog output channel configured as a continuous monitor will scale a user 

input signal into a plus or minus 5 V output signal.  

Input Range

: Input voltage range displayed for reference. 

Output Range

: Output voltage range displayed for reference. 

Track Most Recently Selected

: When enabled, the channel selected in Spike 

Panel, Single Neural Channel, or Raster Plot view is used as the monitor input. 

Channel

: An analog output channel configured as a spike monitor will scale a 

user selected input signal into a plus or minus 5 V output signal. 

Analog Output: Spike Monitor 

An analog output channel configured as a spike monitor will scale a user 

selected input signal into a plus or minus 5 V output signal containing only 

identified spike events. 

Input Range

: Input voltage range displayed for reference. 

Output Range

: Output voltage range displayed for reference. 

 

Figure 19–Analog Output: Continuous Monitor 

 

Summary of Contents for NeuroPort











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands