manualshive.com logo in svg

Blackrock Microsystems NeuroPort, Instructions For Use Manual

Share
Download
Blackrock Microsystems NeuroPort Instructions For Use Manual Download Page 22

 
 
 
 

Revision 1.00 / LB-1070 – NeuroPort Biopotential Signal Processing System IFU 
© 2021 Blackrock Microsystems, LLC 
 

22 

The On/Off switch is located on the back of the unit. Once it is switched on, the APS will 

start a power-up sequence of analog and digital supplies ending with the green ON LED 

illuminating. When the power switch is turned off this sequence is reversed, and the 

output of the APS is tied to ground. In the event of an error in voltage or power delivery, 

the APS will shut down and a red error LED will turn on. After checking all Amplifier and 

patient cable connections for any inadvertent shorting, turn off the APS and turn it back 

on to reset the error. 

Cables 

In addition to the above hardware components, the system also comes with a few 

cables. Note that standard power cables for the NSP and Front End Amp Power Supply 

are included, but not shown below. The fiber-optic cable is used to connect the Front 

End Amplifier to the Neural Signal Processor, the Ethernet cable is used to connect the 

Neural Signal Processor to the recording computer, and the Front End Amplifier Power 

Supply cable is used to connect the Front End Amplifier to its power supply. The Digital 

NeuroPort System does not include the front end amplifier power supply cable. 

 

Figure 8–Fiber-optic Cable 

 

 

Figure 9–Crossover Cable 

 

 

Figure 10–Amplifier Power Supply (APS) Cable 

 

Summary of Contents for NeuroPort











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands