manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, User Manual

The BERTHOLD TECHNOLOGIES LB 480 is a cutting-edge laboratory device that is essential for accurate measurements. To ensure proper usage, don't forget to download the user manual for free at manualshive.com. This manual provides detailed instructions on how to operate and maintain this advanced technology.

Share
Download
background image

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

1 – 93

Volume 1

7 Functional Safety

1

7.3

Other Applicable Documents and 
Records

Depending on the design of the measuring system, the following 
documentation must be observed

The SIL conformity is certified in the attached certificate.

7.4

Detector Identification

SIL-certified detectors are marked on the nameplate with the des-
ignation "SIL" and in the LB number key in addition with an "S" (see 
figure below).

Type

Operating manual

Level measurement

LB 480 Level measurement
ID No. 54733-10BA1L German
ID No. 54733-10BA2L English

Limit level measurement

LB 480 Limit level measurement
ID No. 54733-20BA1S German
ID No. 54733-20BA2S English

Density measurement

LB 480 Density measurement
ID No. 54733-30BA1D German
ID No. 54733-30BA2D English

Identification of a 
SIL certified detector

Summary of Contents for LB 480



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LB 480

Kane 400 Quick Reference Manual preview
400
Brand: Kane Pages: 4
Badger Meter Blancett B3100 Series User Manual preview
Blancett B3100 Series
Brand: Badger Meter Pages: 16
Badger Meter ModMAG M1000 User Manual preview
ModMAG M1000
Brand: Badger Meter Pages: 26
Badger Meter ModMAG M2000 Installation And Operation Manual preview
ModMAG M2000
Brand: Badger Meter Pages: 48
F&F LE-03 Quick Start Manual preview
LE-03
Brand: F&F Pages: 2
IFR COM-120B Evaluation Manual preview
COM-120B
Brand: IFR Pages: 46
Yamaha Clavinova CLP-311 Mode D'Emploi preview
Clavinova CLP-311
Brand: Yamaha Pages: 29
Yamaha ARIUS YDP-S52 Quick Operation Manual preview
ARIUS YDP-S52
Brand: Yamaha Pages: 2
Yamaha Arius YDP-144 User Manual preview
Arius YDP-144
Brand: Yamaha Pages: 15
Yamaha Arius YDP-105 Midi Reference preview
Arius YDP-105
Brand: Yamaha Pages: 3
Yamaha Alto Horn, Baritone, Euphonium Mode D'Emploi preview
Alto Horn, Baritone, Euphonium
Brand: Yamaha Pages: 22
Yamaha Clavinova CLP-320 Quick Operation Manual preview
Clavinova CLP-320
Brand: Yamaha Pages: 2
Yamaha 9000 Pro Service Manual preview
9000 Pro
Brand: Yamaha Pages: 20
VELOCICALC 5725 Operation And Service Manual preview
5725
Brand: VELOCICALC Pages: 10
ColorLite Rugged 2 User Manual preview
Rugged 2
Brand: ColorLite Pages: 68
Bitzer KT-170-4 Technical Information preview
KT-170-4
Brand: Bitzer Pages: 8
PROLEC EA Heightmaster + Operator'S Manual preview
EA Heightmaster +
Brand: PROLEC Pages: 38
i-PRO WJ-NX310K Series Important Information Manual preview
WJ-NX310K Series
Brand: i-PRO Pages: 18

Brands by name

Popular brands

Load more brands