manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, User Manual

The BERTHOLD TECHNOLOGIES LB 480 is a cutting-edge laboratory device that is essential for accurate measurements. To ensure proper usage, don't forget to download the user manual for free at manualshive.com. This manual provides detailed instructions on how to operate and maintain this advanced technology.

Share
Download
background image

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

3 – 427

Volume 3

7 Explanations

3

What to do if 

…

If no suitable DD is available on the HART

®

 Communicator, then 

one of the following two things may happen:

Scenario 1:

The DD on the Communicator is older than the version of the 
embedded software in the SENSseries.

Example: 
DD on the Communicator: 

Dev v1

Field Device Revision: 

Fld dev rev: 2

The following warning is displayed on the Communicator:
This means the DD has to be updated to utilize the full function-
ality of the detector.
Then follows the question: 

Continue with old description? 

Yes/No

 

Select 

Yes

. 

You can continue working normally with the detectors. Only 
new functions that do not yet support the DD are not available.

Scenario 2:

The DD on the  HART

®

 Communicator is more up-to-date than the 

version of the embedded software in the SENSseries:

Example:
DD on the Communicator: 

Dev v2

Field Device Revision: 

Fld dev rev: 1

Then the 

Generic DD

 starts. HART

®

 does not allow that in this 

case an existing DD by the manufacturer will be loaded, as oth-
erwise the program on the Communicator may crash. In the 
Generic DD you cannot calibrate and many parameters for the 
SENSseries are missing.

Universal Revision

All Berthold-DD's require the Universal Commands for HART

®

 6 or 

higher.

This requires that the HART

®

 Communicator by Emerson Process, 

Model 375/475 is used.

Other HART

®

 compatible communicators with HART

®

 6 may also be 

used, provided they support Enhancements.

If the Communicator has a lower version than HART

®

 6, then the 

Generic DD

 will be started.

To determine the version of the Universal Commands, call on the 
HART

®

 Communicator the menu 

Device Config 

 

Setup

 

 

Identifications 

 

Device Revision 

 

Universal Rev.

.

Summary of Contents for LB 480



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LB 480

ICT SFM1 Quick Start Manual preview
SFM1
Brand: ICT Pages: 48
OfiTE 2040 Instruction Manual preview
2040
Brand: OfiTE Pages: 67
Bacharach 2810 Operation & Maintenance Manual preview
2810
Brand: Bacharach Pages: 28
Calsense ET2000 Setup preview
ET2000
Brand: Calsense Pages: 4
Larson Davis System 824 Reference Manual preview
System 824
Brand: Larson Davis Pages: 536
Keithley 6517A User Manual preview
6517A
Brand: Keithley Pages: 343
Keithley 6514 Instruction Manual preview
6514
Brand: Keithley Pages: 334
La Crosse Technology EA-3010 Operating Manual preview
EA-3010
Brand: La Crosse Technology Pages: 2
Stübbe DFM 350 Original Operating Manual preview
DFM 350
Brand: Stübbe Pages: 12
Alpes Lasers ECLK User Manual preview
ECLK
Brand: Alpes Lasers Pages: 41
Thermo Scientific TruDefender FT User Manual preview
TruDefender FT
Brand: Thermo Scientific Pages: 56
Velleman NETBPEM User Manual preview
NETBPEM
Brand: Velleman Pages: 15
3M SP-SE-2-1/1 User Manual preview
SP-SE-2-1/1
Brand: 3M Pages: 168
ICP DAS USA PM-3133-MTCP User Manual preview
PM-3133-MTCP
Brand: ICP DAS USA Pages: 71
CONDTROL xMarker User Manual preview
xMarker
Brand: CONDTROL Pages: 11
Milwaukee 2206-20 Repair Service Instructions preview
2206-20
Brand: Milwaukee Pages: 17
Vectronics SWR-584C Owner'S Manual preview
SWR-584C
Brand: Vectronics Pages: 28
aquilar AquiTron AT-WFM Installation & Operation Instructions preview
AquiTron AT-WFM
Brand: aquilar Pages: 20

Brands by name

Popular brands

Load more brands