manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, User Manual

The BERTHOLD TECHNOLOGIES LB 480 is a cutting-edge laboratory device that is essential for accurate measurements. To ensure proper usage, don't forget to download the user manual for free at manualshive.com. This manual provides detailed instructions on how to operate and maintain this advanced technology.

Share
Download
background image

54733-10BA2L 

2 – 214

02.2017

2 Installation

Volume 2

2.6.6

Point Source Shielding LB744X

Fig. 2-39 Radiation warning sign

Increased radiation dose due to open beam channel!

A too high dose of radiation may be harmful to your health.

A source may be transported only in its shielding. The shielding 
must be closed during transportation and installation.

The radiation exit is cone shaped with an angle of about 10°. During 
installation, the shielding and thus the useful beam must be aligned 
such that they point exactly towards the detector.

Fig. 2-40 Point source shielding

The shielding consists of a lead cylinder with source exit channel 
(7), surrounded by a steel jacket (

Fig. 2-41

). The locking core (6) 

is firmly connected with a lever (4). The "OPEN" and "CLOSED" posi-
tions are secured and the removal of the sources by unauthorized 
persons is prevented by a padlock (3).

The radiation warning sign identi-
fies the start of the controlled area, 
provided the controlled area is 

out-

side 

the shielding. If the controlled 

area is 

inside

 the shielding, then 

the radiation warning sign 
attached on the shielding suffices.

10°

Summary of Contents for LB 480



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LB 480

Calsense ET2000 Setup preview
ET2000
Brand: Calsense Pages: 4
Quantel ULTRA Quick Start Manual preview
ULTRA
Brand: Quantel Pages: 2
GAGEMAKER MIC TRAC MT-3000 Manual preview
MIC TRAC MT-3000
Brand: GAGEMAKER Pages: 20
Magnet-physik FH 52 Operating Instructions Manual preview
FH 52
Brand: Magnet-physik Pages: 32
Grundfos Vortex Flow Industry Instructions Manual preview
Vortex Flow Industry
Brand: Grundfos Pages: 16
Spacelabs 91390 Operation Manual preview
91390
Brand: Spacelabs Pages: 156
Lasertec HV3R Instruction Manual preview
HV3R
Brand: Lasertec Pages: 28
CAS Corporation TW-100 Service Manual preview
TW-100
Brand: CAS Corporation Pages: 20
Sonel CMP-400 User Manual preview
CMP-400
Brand: Sonel Pages: 84
Ratek TH8000 User Manual preview
TH8000
Brand: Ratek Pages: 25
Fora GTel Owner'S Manual preview
GTel
Brand: Fora Pages: 64
VCA sound SMART RLT Sport User Manual preview
sound SMART RLT Sport
Brand: VCA Pages: 36
Xylem Ai1 Series Quick Start Manual preview
Ai1 Series
Brand: Xylem Pages: 39
Fluke 80i-2010s Instructions Manual preview
80i-2010s
Brand: Fluke Pages: 8
IFM SM2 00 Series Operating Instructions Manual preview
SM2 00 Series
Brand: IFM Pages: 45
Panametrics PT878GC Instruction Manual preview
PT878GC
Brand: Panametrics Pages: 224
National Instruments Module NI PXI-8250 Installation Manual preview
Module NI PXI-8250
Brand: National Instruments Pages: 4
Ruide Disteo 23 User Manual preview
Disteo 23
Brand: Ruide Pages: 19

Brands by name

Popular brands

Load more brands